I haven’t posted an update on this project for a several months, so figured it was time.
I now have someone who wants the completed model, so that pushed this project up in priority. Initially, it was more of a test to see what building in paper was like. But, it was so much fun that I kept going with it. Now, it’s close enough to completion to really push to finish it.
I finished building the carriage guns, blackening them and adding breech ropes. For the ropes, I ended up using Morope brand model rope. The main reason for using Morope was simply to test out the product. This model rope certainly looks good, but it does want to unravel quite easily. I found it best to put a drop of CA glue at the point where I want to cut the line. After the CA dries, I cut the line and there’s no unravelling.
The other model rope I was considering was the stuff sold by Syren Ship Model Company. Initially, I avoided this rigging line because for most purposes, the lay of the rope is backwards. It’s all left-hand or S-laid rope. I’ve since changed my mind about the Syren model rope because it’s so nice to work with. It’s stiff, but flexible, doesn’t unravel, and looks great. However, since I already started using Morope, I figured I’d continue with it.
For the cannons, I ended up using turned brass barrels sold by Syren Ship Model Company as swivel guns. One of the sizes worked out perfectly for this models small carriage guns. Making the carriages was the hard part. But, there’s only a dozen to get through.
I then had to add eyebolts at the ends of the breech ropes and drill the bulwarks to mount them. The deck is open and so drilling and adding the eyebolts into place wasn’t too bad. But, the model is more delicate than a wooden one, so it required extra care.
As you can see, the taffrail is pretty well complete. That’s one feature that really made me sweat. Getting those stanchions all in place and then adding the rail and trying to make it run as flat as possible… I’d put off building the rail for a while until I could muster enough nerve to deal with it. Since then, it’s been mostly smooth sailing.
I worked on the sails some time ago. They’re are cloth and purchased as a separate accessory set available from Shipyard. They are pre-printed, but only on one side. Getting the lines of the cloth to show through required lightly tracing them onto the blank side in pencil.
Bolt ropes were glued around the edges using simple white glue. I also added all the small ropes to the two reefing bands on the mainsail.
I’d purchased the masting set from Shipyard too. This just consists of some dowels and a few laser cut cardboard pieces for the cross trees, mast cap, etc.
For blocks, I decided to use some swiss pear blocks I bought from Syren Ship Model Company. They stopped making them rather abruptly and did a big sell-off before I’d had a chance to stock up on more of the sizes I needed. But, this model doesn’t use too many, so I figured I’d go ahead and use them. Anyway, they’re really nice looking blocks. I made up a batch of paper blocks, but I figured I’d use the swiss pear ones while I had them.
Finally, I began the process of rigging by adding the lower deadeyes into place, and rigging the shrouds. As you can see the main boom is also in place. I had to finish up all the details on it first, then decided I’d better add it before too much other rigging gets in the way.
I have to now add all the blocks I’ll need on the mast, gaff and yards and sails. Then, I’m going to have to tie the backstays around the mast head so I can finish up adding the main and preventer stays which will lead down to the top of the stem. Really starting to feel like I’m getting into the home stretch on this model.
One interesting thing I’ve discovered is that the deadeyes are really pretty securely attached on this paper model. That was one thing I had concerns about. But, I wire stropped them and then simply bent the bottom of the wire to insert into holes I drilled into the hull, forming the chainplate. A faux chainplate is then glued to the face of the wire.